![]() R1#show ip route Codes: L - local, C - connected, S - ST, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user ST route o - ODR, P - periodic downloaded ST Interface IP-Address OK? Method Status ProtocolįastEthernet0/0 10.1.1.1 YES manual up upįastEthernet0/1 192.168.5.1 YES manual up upįastEthernet0/0 10.1.1.2 YES manual up upįastEthernet0/1 192.168.10.1 YES manual up up Pinging will be successful if you ping from Windows 10 to a Windows 8.1 machine on the 192.168.5.0/24 network. When you Ping from Windows 8.1 to the Windows 10 machine on the 192.168.10.0/24 network, Ping will succeed as follows. In the same way, add ST Route to Router R2 and check it with the show ip route command. You can also control the static route using the show ip route command on R1. + - replicated route, % - next hop overrideġ0.0.0.0/8 is variably subnetted, 2 subnets, 2 masksĬ 10.1.1.0/24 is directly connected, FastEthernet0/0 O - ODR, P - periodic downloaded ST route, H - NHRP, l - LISP Ia - IS-IS inter area, * - candidate default, U - per-user ST route I - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2Į1 - OSPF external type 1, E2 - OSPF external type 2 R1#conf tĮnter configuration commands, one per line. Use the following commands to add a static route for R1. Now, you need to add ST Route on Router R1 and R2 to communicate virtual machines. The reason for this because no routing protocols configured, Windows 8 cannot access the Serial interface of Router R2.ĭo the same on the Windows 10 machine and observe that the ping failed for the 192.168.5.0/24 network. ![]() Pinging from Windows 8 to the Fa0/2 interface of Router R2 will also fail as follows. This is where the importance of ST Route or dynamic protocols emerges. R2(config-if)# ip address 10.1.1.2 255.255.255.0īefore you configure Static Route, this will fail when you ping the Fa0/0 interface of Router R2 from Windows 8. In the same way, configure the Fa0/0 interface of Router R2. Pinging from the Windows 10 machine to the Fa0/1 interface of Router R2 will also be successful.Ĭonfigure the FastEthernet0/0 interface of the Cisco Router R1. When pinging the Fa0/1 interface of the Cisco Router R1 from the Windows 8 machine, and you will see that the connection was successful. In the same way, configure the interface to which the 192.168.10.0/24 network connected to the Cisco Router R2. Check your configured interfaces with the show ip interface brief command. Open the Cisco Router R1 CLI prompt and configure the FastEthernet 0/1 interface. In the same way, configure the IP address of the Windows 10 virtual machine on VMware Workstation as follows. You can also provide a clearer understanding of the network topology by adding comments.Ĭonfigure the IP address settings of the Windows 8.1 virtual machine on VMware Workstation as follows. In the GNS3 program, create a network topology as shown in the image below. Open the GNS3 program for Static Route and create a new project.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |